rsistoch wrote: Fri May 30, 2025 9:57 am I just find it gives wrong signal.
Below is an example of XAU, DB gives Down signal but PR on chart is Up.
This is a useful indicator in VZU's system, it signals a potential reversal point.
BTW FNC TDI is working correctly.
TYSM!

I am looking at the histogram of the current bar.
I cannot see it but I am comparing red and blue.
How can I do this?
Please explain as I am not familiar with the various indicators.

funchi wrote: Fri May 30, 2025 10:30 am I am looking at the histogram of the current bar.
I cannot see it but I am comparing red and blue.
How can I do this?
Please explain as I am not familiar with the various indicators.

i guess DB is getting signals with values ​​outside the buffer range, from my limited knowledge PR's buffer has a range of 8 to 23.
We need DB to get valid signals which it shows on the most recent chart.
In the XAU image i posted it is Up.
I am not an experienced MT4 programmer, please ignore if my opinion is wrong.

rsistoch wrote: Fri May 30, 2025 10:52 am i guess DB is getting signals with values ​​outside the buffer range, from my limited knowledge PR's buffer has a range of 8 to 23.
We need DB to get valid signals which it shows on the most recent chart.
In the XAU image i posted it is Up.
I am not an experienced MT4 programmer, please ignore if my opinion is wrong.

I want to know under what conditions I want to display an up signal.
I want to know under what conditions I want to display a down signal.
I would like to know under what conditions I would like to see a flat signal.

For example,
A down signal is shown when blue is displayed.
Red indicates an up signal.
Show a flat signal when black is displayed.

funchi wrote: Fri May 30, 2025 8:07 am For example, setting the decision bar to 4 will result in a delayed decision.

Sorry.
When dealing with Semafor in a system, it is impossible to explain in a few words.
I am still not convinced by the Semafor signals.

It is very difficult.

As you can see in the image, when the triangle is formed, a signal is issued. I want the signal to remain the same, either a sell or buy signal, until another triangle is formed and a sell signal is issued. thank you.

funchi wrote: Fri May 30, 2025 2:56 pm I want to know under what conditions I want to display an up signal.
I want to know under what conditions I want to display a down signal.
I would like to know under what conditions I would like to see a flat signal.

For example,
A down signal is shown when blue is displayed.
Red indicates an up signal.
Show a flat signal when black is displayed.

blue is buy
red is sell
About how to use this indicator, a simple example of a Buy trade according to what I understand:
Trading time frame H1 H4
Wait for PR blue (up) to appear on H4
Then wait for a change in market structure to appear on H1 and at the same time the indicators 3xu ma, kingfisher, Jurik volty are all Up to confirm.
This is the easiest and safest way to use to increase the win rate.
Trade more aggressively. After PR H4 appears, just wait for the 3 indicators on H1 to be UP without confirming the change in market structure.
I will post a picture to make it easier to understand because my English is poor.
Pay attention to the time the PR appears on H4 and the time the entry is confirmed on H1.
Most of the time after the entry is confirmed the PR indicator will be black, so we should take the signal from the blue or red histogram appearing on the most recent chart within the buffer range of 8-23.
In some cases the entry is confirmed after it has gone far past the time the PR appeared, I think we should ignore it and wait for another PR to appear later.

rsistoch wrote: Fri May 30, 2025 6:32 pm blue is buy
red is sell
About how to use this indicator, a simple example of a Buy trade according to what I understand:
Trading time frame H1 H4
Wait for PR blue (up) to appear on H4
Then wait for a change in market structure to appear on H1 and at the same time the indicators 3xu ma, kingfisher, Jurik volty are all Up to confirm.
This is the easiest and safest way to use to increase the win rate.
Trade more aggressively. After PR H4 appears, just wait for the 3 indicators on H1 to be UP without confirming the change in market structure.
I will post a picture to make it easier to understand because my English is poor.
Pay attention to the time the PR appears on H4 and the time the entry is confirmed on H1.
Most of the time after the entry is confirmed the PR indicator will be black, so we should take the signal from the blue or red histogram appearing on the most recent chart within the buffer range of 8-23.
In some cases the entry is confirmed after it has gone far past the time the PR appeared, I think we should ignore it and wait for another PR to appear later.

Is this it?

funchi wrote: Fri May 30, 2025 10:03 pm Is this it?

Yes it works correctly.
Jurik volty bands Average.
This is the final indicator to complete the VZU system.
Green for buy and red for sell.
I also attach the setup file of the indicator.
Looking forward to receiving the signal of this indicator from Funchi san's FNC DB.

TYSM Master Funchi!!!

asgariHoo wrote: Fri May 30, 2025 5:26 pm Screenshot 2025-05-30 104905.jpg As you can see in the image, when the triangle is formed, a signal is issued. I want the signal to remain the same, either a sell or buy signal, until another triangle is formed and a sell signal is issued. thank you.

As requested, although in some cases there are signals of concern.

funchi wrote: Fri May 30, 2025 11:35 pm As requested, although in some cases there are signals of concern.

Excellent. Thank you, Mr. Funchi.
Mr. Funchi has a question: How can I get a faster signal from FNC CSS?
Also, I had a FNC TDI check, but I don't think it worked properly. think need to add only RSI crosses MBL.thanks

asgariHoo wrote: Sat May 31, 2025 2:35 am Also, I had a FNC TDI check, but I don't think it worked properly. think need to add only RSI crosses MBL.thanks

RSI crosses MBL