funchi wrote: Sat Oct 04, 2025 10:14 am Which indicator are you referring to?
Is it an indicator called IMDB_FX?
Where can I download it from?
What are the signal conditions?


By the way, I’ve deleted all of the old FNC_DB-related files and no longer have them on hand.
At the moment, I can only provide support for the two versions shown in Post #1 – one for MT4 and one for MT5.

RYSIO wrote: Sun Oct 05, 2025 5:09 am The indicator is IMBD_FX . I only have the ex, version . The signal from the indicator is released after crossing the 0 line. An up signal is for a long position, and a down signal is for a short position. It would be great if it matched the version shown in Post#1 ,for MT4.

funchi wrote: Sat Oct 04, 2025 10:09 am Sorry, I didn’t explain things clearly enough earlier. Here’s my suggestion - please feel free to let me know if you have any other ideas.
I’ve made some changes to the signal indicator "FNC_Zee_SupRes".
Please download the updated version and replace the old one.
With this update, when you set the "Bars to check" value, the indicator will only retrieve information within that specified range.
Therefore, even if there is indicator data outside of that range, signals will not be displayed.
For example:
If you set "Signal bar" to 1 and "Bars to check" to 1,
the indicator will only check one bar before the current bar.
If you set "Signal bar" to 1 and "Bars to check" to 10,
the indicator will check from one bar before the current bar, going back 10 bars in total.

funchi wrote: Sun Oct 05, 2025 3:58 pm A new signal indicator has been added.

newbietrader1 wrote: Tue Oct 07, 2025 2:59 am Thanks for the explanation Mr Funchi!

Then I guess I should set the 'Bars to check'' to 1? I just want to enter the trade right away when the FNC_Zee_SupRes has appear, and not enter when the FNC_Zee_SupRes signal is too far away, whether it is uptrend or downtrend.

That should sound correct right?

I have set the 'Bars to check' to 1, but the system went into trade as shown, is there anything I have missed out?

newbietrader1 wrote: Thu Oct 09, 2025 2:03 am FNC BEAT V5 TESTING INDICATOR CHART - 8.10.2025.tpl


FNC BEATV5 DASHBOARD - 8.10.2025 LATEST.tpl

• Entry signals can now be forwarded from MT4 to MT5.
• Entry signals can be forwarded from MT5 to MT4.
• Entry signals can be forwarded from one PC to another, limited to the same network.

• Forward the entry signals from the FNC_DB strategy created with an indicator available only on MT4 to MT5.
• Alternatively, do the reverse.
• Forward high-load FNC_DB strategy signals to a lower-performance PC.
• Copy signals to another account for automated trading.

• The signals are transmitted over a network using TCP.
• The ports used range from 49000 to around 10000 ports higher or lower.
• The "Pairing ID" parameter is set within the range of 10000 to -10000.
• The transmission is limited to the same local network, so no data will be transmitted externally.

• This indicator sends entry signals.
• Add it to the same chart window as the FNC_DB.
• It does not display as a signal column.
• The "Receiver hostname or IP address" parameter should be set to the name or IP address of the receiving PC.
• The "Pairing ID" parameter must match between the sending and receiving sides.

• This indicator receives entry signals.
• Add it to the same chart window as the FNC_DB.
• It will display as a signal column.
• The "Pairing ID" parameter must match between the sending and receiving sides.
• You can configure currency pair conversion.
• Set to remove the suffix of the currency pair on the sending side's broker.
• Set to add the suffix of the currency pair on the receiving side's broker.
• If the currency pair names are completely different, a conversion table can be set. Example: JP225=NIKKEI, DAX=GER40, DOW=US30.

• A status lamp has been added near the button of FNC_DB.
• If the button is hidden, the status lamp will also be hidden.
• Green: Operating normally.
• Yellow: Unable to connect between sending and receiving sides.
• Red: Error detected.
• Details can be viewed via tooltip.

• A security warning window will appear once on Windows.
• To continue using it, allow access.
• Some network configurations (e.g., router settings) may be required, but this is typically not necessary for most users. I am unable to provide support for these setups, should they be needed.

• I have only tested signal sending and receiving within the same PC.
• Since I only own one PC, I have not tested forwarding signals to another PC.
• In theory, it should work, but please inform me of any issues.