Hi All, it is my first post here, however I am trying to trade with the system and observe it for over 1 year. I understand the principal and I have seen all the pictures and explanations here, however I find extremely difficult to find my entry points and how to position my SL and TP, as the dots are dynamic. I focus on Gold only and my intention is to bite off a 20 pip profit from the trends with max SL 20 pip or lower if possible on 1 min Chart. However, as said I am struggling to find the approach to those entries with higher win rate.
Can someone help me with finding a repetitive conditions for entries in the dynamic environment in the system? Currently I am focused on the v10 and the chart from Neroloft (I find this one very clear).

Dear Mr. Xard777,
i know it is not allowed to ask for any source code. Therefore i don´t know to ask the right way, but is there a possibility you can share your XU-v78 VWAP Indicator? I would like to recode it into MQL5 and willing to re-share it here, when done. If not, it´s okay for me, just wanted to ask you kindly. I really like the indicator and haven´t found anything similar to that. Even in M5 it is a good indicator for Swings.
Best regards,
Redman
XARD: Here you go...

Hello Funchi,

First let me thank you for the incredible work you make, it's really great.

I have a request if possible concerning your version 2.0 of your indicator.

You see in my screenshot on my red vertical line, your indicator said short with red bars, but if the price climbs up above the open line, the red bars disappears. And your older versions didn't do that.

I think in this way, it is too much repainting, can you please revert back to the old logic but you keep the ADR, it's fantastic to filter the bad trades.

If it's not possible don't worry

Redman wrote: Thu Jun 06, 2024 11:51 pm Dear Mr. Xard777,
i know it is not allowed to ask for any source code. Therefore i don´t know to ask the right way, but is there a possibility you can share your XU-v78 VWAP Indicator? I would like to recode it into MQL5 and willing to re-share it here, when done. If not, it´s okay for me, just wanted to ask you kindly. I really like the indicator and haven´t found anything similar to that. Even in M5 it is a good indicator for Swings.
Best regards,
Redman
XARD: Here you go...

Thank you very much !!!

Hi Neroloft, I am writing to you privately so as not to contradict Xard as he does not like the m1 timeframe at all.
* he used to trade M1. xard setup can be traded in all timeframes

I really like it instead, but I can't find a valid exit rule for trades using Xard's system.
* try vwap

How do you calculate TP?
** i use 1:3 RRR

Do you stay on m1 or do you also look at m5 or m15 to confirm the trend?
* better use xard's recommended tfs, for now i stick with setups coming from m1/m5

I thank you in advance if you want to answer me.
*check this PDF

Neroloft wrote: Thu Jun 06, 2024 4:33 pm xard setup is always on the chart

please can you send me the Template of your setup today? thank you.

funchi wrote: Thu Jun 06, 2024 12:27 pm I have created a versatile XARD signal("FNC_XARD_Signals"). This is the so-called version 2.
[...].
The method of determining the MA 55-13 cross is different.
Differences due to not using the v65m source code as a reference.
[...]
New feature added in version 2.
MA cross.
[...]
Please let me know if there are any problems.

Hi funchi,
thank you for this gem.
Can you please clarify these:
1) Do you confirm that FNC_XARD_Signals version 2 runs completely independent from Xard Universe and there is no need to install Xard Universe at all to use your indicator ?
2) While MA13 from Xard Universe v65m and MA13 from your indicator version 2 look identical, there are visible differences between MA55 line from XARD Universe v65m and MA55 line from your indicator ( shown in ribbon ), please see attached images. Can you tell me the reasons behind these differences ?

Thanks,
Mork01

LittleCaro wrote: Fri Jun 07, 2024 12:06 am Hello Funchi,

First let me thank you for the incredible work you make, it's really great.

I have a request if possible concerning your version 2.0 of your indicator.

You see in my screenshot on my red vertical line, your indicator said short with red bars, but if the price climbs up above the open line, the red bars disappears. And your older versions didn't do that.

I think in this way, it is too much repainting, can you please revert back to the old logic but you keep the ADR, it's fantastic to filter the bad trades.

If it's not possible don't worry

You need to make sure that ADR is working correctly.
Perhaps ADR is not working correctly.

Attached is the image, and here is the description of the indicators, starting from the top.
“FNC_XU v65m-XARD_Signals” with default parameters.
“FNC_XU v010-XARD_Signals” with default parameters.
FNC_XARD_Signals” parameter is the default value.
FNC_XARD_Signals” and the parameter ‘ADR’ is disabled.

Sorry. Please wait a moment.

Mork01 wrote: Fri Jun 07, 2024 3:21 am Hi funchi,
thank you for this gem.
Can you please clarify these:
1) Do you confirm that FNC_XARD_Signals version 2 runs completely independent from Xard Universe and there is no need to install Xard Universe at all to use your indicator ?
2) While MA13 from Xard Universe v65m and MA13 from your indicator version 2 look identical, there are visible differences between MA55 line from XARD Universe v65m and MA55 line from your indicator ( shown in ribbon ), please see attached images. Can you tell me the reasons behind these differences ?

Thanks,
Mork01

Yes.
Works independently of the Xard system.
The indicator for the Xard system does not need to be installed.
Instead, the attached indicator needs to be installed.

I am aware of this.
If you need an exact match to v65m, use “FNC_XU v65m-XARD_Signals”.
Also, if you need a way to determine MA crosses for v65m, for example, because you are creating your own Xard system by combining indicators from different versions, please let us know.

funchi wrote: Fri Jun 07, 2024 8:27 am Yes.
Works independently of the Xard system.
The indicator for the Xard system does not need to be installed.
Instead, the attached indicator needs to be installed.

I am aware of this.
If you need an exact match to v65m, use “FNC_XU v65m-XARD_Signals”.
Also, if you need a way to determine MA crosses for v65m, for example, because you are creating your own Xard system by combining indicators from different versions, please let us know.

Thanks funchi.
I'm ok with MA's from version 2.
From graphical perspective it would be nice for me to have the FNC_Ribbon not overlapping the candles as in original Xard and also the Xard candles 3 colors scheme based on the MA cross. Have you or anybody something similar ?