funchi wrote: Wed Jun 14, 2023 8:45 pm Operation check, seems to be OK.
I will upload it tomorrow.

That looks super Funchi!

Woodyz wrote: Wed Jun 14, 2023 8:56 pm Hi Funchi, I just want to clarify something with this EA.
Once setup can it also be run to give signals only for manual trade entries and exits?

yes, funchi's dashboard has alerts

Woodyz wrote: Wed Jun 14, 2023 8:56 pm Hi Funchi, I just want to clarify something with this EA.
Once setup can it also be run to give signals only for manual trade entries and exits?

This time,
Upload the settings so that the automatic trading will not be executed automatically.
The EA is built in, but will not automatically trade unless the start button is pressed.
The default setting is manual entry/exit.

funchi wrote: Wed Jun 14, 2023 5:48 pm What is the URL to upload or download the indicator?

Hello my friend, here are the indicators!!!!, the idea is to always use the supertrend at higher times to show a good trend, and use the halftrend to make the entries following the supertrend!

こんにちは、私の友人、ここにインジケーターがあります。アイデアは、良いトレンドを示すために常に高い時間帯でスーパートレンドを使用し、スーパートレンドに従ってエントリーを行うためにハーフトレンドを使用することです。

thanks you my friend

1337br wrote: Wed Jun 14, 2023 11:30 pm Hello my friend, here are the indicators!!!!, the idea is to always use the supertrend at higher times to show a good trend, and use the halftrend to make the entries following the supertrend!
thanks you my friend

I will create a signal, though,
I am not a good learner,
I don't know how to use supertrend and halftrend.
Please post the conditions of the signal or give me a URL where I can find out how to use them.

Improvements.
The EAs are mainly described, but so are the trading signals.


The differences are as follows.


Before change
Signals are created by
The signal is created 5 seconds after the time of the time frame, not waiting for the next candle to occur.
The trade is executed 20 seconds later.
When the time is up, the signal is created with the current state of the signal.


After the change
Wait for the next candlestick to occur before creating the signal.
The trade is executed after the signal is created.
Unless the next candlestick occurs,
Signals are not created and trades are not executed.


This is as it has always been. Basic premise of entry conditions.
Immediately after you start trading EA,
already past signals are not eligible for entry.
No entry will be made once the 1-bar (initial value) is exceeded.


There is a new caveat.


Before the change,
Entry/exit was made on the time frame.
No entry/exit from the middle of the time frame.

After the change,
If there is a signal to enter/exit, it will be executed regardless of the time.


In addition, the alerts will remain the same,
Alerts will be sent after waiting 30 seconds from the time on the time frame.


<Download>
In preparation.

Small known glitches

After an entry condition is broken, even if the entry does not exit,
If the entry conditions are met again,
The new entry signal will be displayed as a new entry signal and an alert will be displayed.

EA is not affected.

This is the "X-Gen" version of the "FNC Greedy System."
Template name is "FNC Greedy System_X-Gen.tpl"

NOTES.
Squeeze and divergence are not included in the conditions.
Therefore, this tool filters the entry targets,
used as a guide for X-Gen.

Squeeze and divergence are not programmed.
They will be created after information is collected.
I need information.


Buy Entry
If all directions match, I will enter.
Will post if details are requested.

Exit
when the 5EMA crosses back over the 13EMA.

Please point out if I am wrong.
Please post any additional requests.

I have also incorporated the EA,
After loading the template, it does not trade automatically.
Manual entry/exit is assumed.

<Download>

Uploaded the latest version.
Please download from post #1.
Version 23.065
viewtopic.php?p=1295507591#p1295507591

Sorry,

Uploaded again.

Please discard "The FNC Greedy System_20230615_1400".

"The FNC Greedy System_20230615_1500" is the latest.

Hi Mate

Tried running the installer.
Created the new folder "FNC"..enter...then get wrong folder message......

I'm a bit lost............how do we run the installer............which folder? etc